Goldie’s First Trip

Well Independence Day arrived much sooner than expected this year and before we knew it we were packing up the trailer and hitting the road for our first trip ever in our 1971 Aristocrat Starliner AKA “Goldie”.  In honor of freedom day I chose not to register the trailer thanks to three failed attempts at the DMV to get it done (that’s another story).  So we hit the road in our unregistered antique packed full of camping gear and beer.

We spent 3 nights up at Beaver Campground in Washington and our group had 3 campsites occupying a nice little cul-de-sac at the edge of the campground near the river.  We decided we would treat this trip as a trial with the trailer and it would be a good opportunity to see how everything functioned.

Stuff that Worked

Towing the trailer was a breeze.  In the RPOD we rented 2 years ago the Yukon had a tough time pulling it and I had to manually put the transmission in 3rd gear so I wouldn’t tear it up.  On this trip we headed out I84 up the gorge and I kept it between 60 and 65 with no transmissions issues at all.  I would like to attribute this to the fact that I greased up the wheel bearings before we left but there is no real way to know.

The toilet seemed to work just fine and the entire water system was great.  We did run out of water the last day but we were indiscriminately using h20 due to the fact that there was a spigot about 30 feet from our campsite where we could get more water.  For true “boon-docking” trips we will need to use water more sparingly.

The LED nightlights I installed worked great.  We had them on every night and it made midnight trips to the bathroom a breeze and kept things lit up just enough to see but not enough to keep us awake.

12v electricity was fine and the lights in the trailer seemed to be more than sufficient.  The pump worked and the tank sensors were functioning as well.

The stove worked well and gas lines did not give us any problems.  The oven is still not working though and I need to figure out where the plug up is in the gas line.

Stuff that Didn’t Work

Electricity.  I figured the solar panel would work well enough to power our batteries back up while at the same time running a little refrigerator but it was not enough.  I am fairly certain this would have worked had we been in direct sun light but we were camped in a very shaded area and it just did not produce enough electricity to do both.  If we just wanted to power up the batteries it would have been fine.

Additionally the power inverter battery combo was not strong enough to brew a pot of coffee.  It would run and could make the pot but the batteries drained pretty fast and the inverter started beeping out a low power warning.  Looks like we will need an alternative for coffee or a generator.

Dishes and such.  We need more.  Did not have enough coffee mugs for 4 people and it will be nice to make coffee for friends in the morning on these trips.

While towing I also noticed that I really could not see around the back of the trailer with my mirrors.  It is pretty wide at 8ft and I had no idea if a car was behind me or not and backing it up was also pretty difficult.  I found some mirrors on Amazon that will snap on to my existing GMC mirrors and will be using those on the next trip.  You can find those here for about $40: CIPA 10800 Chevrolet/GMC Custom Pair Towing Mirrors

Will be Ready for the Next Trip

Overall everything went smoothly – even more smooth than I expected.  The biggest hassle is getting the trailer back up our mountain of a driveway and I am only going to be able to put up with that for so long.  Looks like we will be renting a spot to star old Goldie sooner than expected.  Can’t wait for our next trip!

IMG_7506

Goldie’s Interior

Here are a couple shots of the inside of Goldie (yes, that’s what were calling her since we did gold accents). Lot’s of work but it paid off and looks great! Still not totally done with the kitchen backsplash so you’re not seeing that part. More interior shots to come!

A Quick twirl around the trailer….

Rebuilding the Hub Assembly

After our trip to Yellowstone a few years ago where we broke down in the middle of the park because our wheel bearings were bad on the trailer we rented I decided it would be a good idea to rebuild the hub assembly on the Aristocrat Starliner. I was originally just going to purchase and entire new axle with a builtin hub, brakes and new leaf springs but finding an axle that was the right size was nearly impossible.  I also noticed that the leaf springs that came with our trailer are pretty beefy and decided to just keep it as is for now.

Instead, I settled for rebuilding the hub assembly with new bearings, racers and grease seals.  With no experience doing this I watched a few videos on youtube and then headed outside and yanked the tired off the trailer and then removed the hub assemble.  To get the hub assemble off you actually have to remove the dust cap on the outside of the axle which will expose the castle nut that is held in place by a cotter pin.  Pull the pin and then remove the castle nut.  Once that is off the hub should just slide right off but be careful as there is a big washer under that castle nut and you exterior bearing will likely fall right out.

The exterior bearing is a Timken M12649  which is incredibly easy to find on Amazon. It does not come in a set though and requires some searching for the racer that goes with the bearing.  After doing some research and being sold the wrong part by Six Robblees I finally found the race model:  M12610.  You can find the specs for both parts on the Timken Site here: http://cad.timken.com/item/tapered-roller-bearings-ts-tapered-single-/tapered-roller-bearings-ts-tapered-single-imperi-2/item-27350

The inner bearing is also a Timken however is a different model – it is a Timken LM48548.  The race for his bearing is a Timken LM48510 and you can find specs for both parts here: http://cad.timken.com/item/tapered-roller-bearings-ts-tapered-single-/tapered-roller-bearings-ts-tapered-single-imperi-2/item-29219 I was able to find both Timken Bearins and both Timken Racers with a brief phone call to Napa Auto parts.

In an interesting find I realized that the grease seals on each hub were different. Someone must have replaced one of them so I am not sure which is the “true” original. On of the hubs I found a seal that was stamped with a “2M – HADCO – 3077 ” label on it.  Apparently these are incredibly hard to find.  I could not find anything online about this except for a blog post someone else with an old Aristocrat (not a Starliner) had written about.  She suggested getting in touch with Six Robblees which is a store that specializes in trailer parts.  I went there and they had to special order the seals from the store in Oakland.  The seals they sent are labeled part number: AE2592N and I really cannot find anywhere online where you can buy these.  I ordered three so I would have a backup. The other hub had a Seal that was stamped with a “National – 442251 – S60” on it. I found these ones on Amazon here: National Oil Seals on Amazon.

 

Interior Colors

After lots of different ideas (I wrote a whole post on what I wanted to do and am not doing that anymore) I’ve came up with the simple design of white everything, and gold accents.

Main interior colors – I chose a white, BEHR MARQUEE interior pain in high gloss with a mold/mildew resistant primer and gold spray paint from Krylon’s Color Master collection with their spray primer.

Below is what I’ve done to the window frames and they look fantastic!

Primed them with 2 coats:

IMG_6802

 

 

 

 

 

 

 

 

Then sprayed them with 2 coats of gold:

I’ve also purchased the peel and stick backsplash from Amazon.com

backsplash

 

 

 

 

 

 

 

 

And the flooring which is Peel and Stick in Rustic Oak, bought from Walmart.com

floor

 

 

 

 

 

 

 

 

 

 

It’s coming along. Chris has done most of the electrical and plumbing. We’re over half way there!

Interior Inspiration: Paint/Flooring/Backsplash

While Chris continues to fix the dry rot and water damage on the trailer (which I’m not much help with); I’ve looked and looked to find something that “speaks to me”. At this very moment, I share with you my current vision. I’m actually pretty excited about this.

Screen Shot 2015-02-01 at 10.27.34 AM

The picture above I’m in love with (and want to copy for my house, hehe). I love the earth tone colors and woods of this house that bring the outside in. For our trailer, we’ll have to use a lot more white to make the inside light and bright since it’s a lot smaller. So here is what I’m thinking.

Top Lt: Vesdura Vinyl Peel & Stick in Teak Cocoa; Top Rt: Vesdura Vinyl  Peel & Stick in Natural Oak; Middle Rt: Mosaik Self Adhesive High-Gloss Mosaic in White; Paint: Behr in Burnished Bronze, Summer Field, and/or Venetian Gold
Top Lt: Vesdura Vinyl Peel & Stick in Teak Cocoa;
Top Rt: Vesdura Vinyl Peel & Stick in Natural Oak;
Middle Rt: Mosaik Self Adhesive High-Gloss Mosaic in White;
Paint: Behr in Burnished Bronze, Summer Field, and/or Venetian Gold

Kitchen Backsplash: BuildersDirect.com has a peel & stick vinyl in Teak Cocoa. The only issue is they sell it in quantities of 2500 sq/ft. So I’m emailing them to see if they would be able to sell me like 5 sq/ft. Ha! We’ll see.

Cabinet Drawer facings: To give the cabinets a small detail, I like the idea of refacing them in and Mosaik – peel & stick Mosaic White tile I found on Wayfair.com.

Paint: Most of the trailer and ceiling will be Behr Powdered Snow, white. Small accents will be in the Gold/yellow tones shared above.

Floors: I like this Natural Oak from Buildersdirect.com. Same issue though. I’m going to email them to see if they will sell me a smaller quantity.